AWS B2.1-1-012:2002 pdf download

AWS B2.1-1-012:2002 pdf download.Guidelines for Preparation of Technical Inquiries for AWS Technical Committees
All inquiries must be directed to: Managing Director, Technical Services American Welding Society 550 N.W. LeJeune Road Miami, FL 33126 All inquiries must contain the name, address, and af- filiation of the inquirer, and they must provide enough in- formation for the committee to fully understand the point of concern in the inquiry. Where that point is not clearly defined, the inquiry will be returned for clarification. For efficient handling, all inquiries should be typewritten and should also be in the format used here. A2.1 Scope. Each inquiry must address one single pro- vision of the standard, unless the point of the inquiry involves two or more interrelated provisions. That provi- sion must be identified in the scope of the inquiry, along with the edition of the standard that contains the provi- sions or that the inquirer is addressing. A2.2 Purpose of the Inquiry. The purpose of the inquiry must be stated in this portion of the inquiry. The purpose can be either to obtain an interpretation of a standard requirement, or to request the revision of a particular pro- vision in the standard. A2.3 Content of the Inquiry. The inquiry should be concise, yet complete, to enable the committee to quickly and fully understand the point of the inquiry. Sketches should be used when appropriate and all paragraphs, fig- ures, and tables (or the Annex), which bear on the in- quiry must be cited. If the point of the inquiry is to obtain a revision of the standard, the inquiry must provide tech- nical justification for that revision. A2.4 Proposed Reply. The inquirer should, as a pro- posed reply, state an interpretation of the provision that is the point of the inquiry, or the wording for a proposed revision, if that is what inquirer seeks.
B2.1:2000 Specification for Welding Procedure and Performance Qualification B2.1-001-90 Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1, Group 1 or 2), 3/16 through 3/4 inch in the As-Welded Condition, With Backing B2.1-002-90 Standard Welding Procedure Specification (WPS) for Gas Tungsten Arc Welding of Carbon Steel (M-1/P-1, Group 1 or 2), 3/16 through 7/8 inch in the As-Welded Condition, With or Without Backing B2.1-1-003:2002 Standard Welding Procedure Specification (SWPS) for Gas Metal Arc Welding (Short Circuiting Transfer Mode) of Galvanized Steel (M-1), 18 through 10 Gauge, in the As-Welded Condition, with or without Backing B2.1-1-004:2002 Standard Welding Procedure Specification (SWPS) for Gas Metal Arc Welding (Short Circuiting Transfer Mode) of Carbon Steel (M-1, Group 1), 18 through 10 Gauge, in the As-Welded Condition, with or without Backing B2.1-8-005:2002 Standard Welding Procedure Specification (SWPS) for Gas Metal Arc Welding (Short Circuiting Transfer Mode) of Austenitic Stainless Steel (M-8, P-8, or S-8), 18 through 10 Gauge, in the As-Welded Condition, with or without Backing B2.1-1/8-006:2002 Standard Welding Procedure Specification (SWPS) for Gas Metal Arc Welding (Short Circuiting Transfer Mode) of Carbon Steel to Austenitic Stainless Steel (M-1 to M-8, P-8, or S-8), 18 through 10 Gauge, in the As-Welded Condition, with or without Backing B2.1-1-007:2002 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding of Galva- nized Steel (M-1), 18 through 10 Gauge, in the As-Welded Condition, with or without Backing B2.1-1-008:2002 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding of Carbon Steel (M-1, P-1, or S-1), 18 through 10 Gauge, in the As-Welded Condition, with or without Backing B2.1-8-009:2002 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding of Austenitic Stainless Steel (M-8, P-8, or S-8), 18 through 10 Gauge, in the As-Welded Condition, with or without Backing B2.1-1/8-010:2002 Standard Welding Procedure Specification (SWPS) for Gas Tungsten Arc Welding of Carbon Steel to Austenitic Stainless Steel (M-1, P-1, or S-1 to M-8, P-8, or S-8), 18 through 10 Gauge, in the As-Welded Condition, with or without Backing